Hard Water From a Well: What to Do

Disclosure: This page contains affiliate links. If you buy through one, we may earn a commission at no extra cost to you. It doesn't change what we recommend.

By Jeff McKelvey · Jeff runs JMedia Local in Dadeville, Alabama, and researches well-water treatment for homeowners dealing with iron, sulfur, and hard water.

Last updated: November 19, 2026

Prices re-checked: November 19, 2026

Water spots beaded on glass from hard water

What hard water is

Hardness is dissolved calcium and magnesium in your water. It comes from the ground — water passing through limestone and chalk picks up minerals on the way to your well. It isn't a health concern. The USGS calls it a nuisance, and that's accurate: it doesn't make you sick, it just makes everything else harder. Scale in the kettle, spots on the glassware, soap that won't lather, laundry that comes out stiff, a water heater slowly choking on mineral buildup.

Hardness is measured in grains per gallon (gpg) or milligrams per liter (mg/L, the same as ppm). One grain per gallon equals 17.1 mg/L. Your lab report may use either — divide mg/L by 17.1 to get gpg. The USGS scale:

Classificationmg/L as CaCO3Grains per gallonWhat you notice
Soft0–600–3.5Soap lathers easily, little scale. No treatment needed.
Moderately hard61–1203.6–7.0Some spotting, soap less effective, mild scale possible.
Hard121–1807.1–10.5Noticeable scale, soap scum, dull laundry, appliance wear.
Very hardOver 180Over 10.5Heavy scale, clogged aerators, water heater efficiency loss.

Most well owners start thinking about treatment around 7 gpg. Above 10.5, most homes soften — the scale damage to a water heater alone pays for the system over a few years.

Test your water before buying anything. You need the hardness number in gpg, and you need to know whether iron is riding along with it — that changes the system. How to Test Your Well Water.

The honest difference: softener vs conditioner

This is the most misleading argument in home water treatment, and it's worth getting straight before you spend money.

A salt-based ion-exchange softener removes hardness. Water flows through a resin bed, and the resin swaps calcium and magnesium ions for sodium (or potassium) ions. The hardness minerals are physically gone from the water leaving the tank. A test after the softener reads soft. This is the only technology certified under NSF/ANSI Standard 44, which is the actual standard for water softening. It needs salt, a drain for regeneration, and electricity.

A salt-free "softener" does not remove hardness. These systems use template-assisted crystallization (TAC) — water passes through a media bed that encourages calcium and magnesium to form microscopic crystals that stay suspended instead of sticking to surfaces as scale. The minerals are still in the water. A test after a TAC unit reads exactly as hard as before. Total dissolved solids are unchanged. Spots on glassware? Still there — spots are dried minerals, and the minerals never left. Soap lather, laundry feel, skin and hair? Unchanged, because those depend on actual hardness removal.

TAC isn't a scam. Independent testing under the German DVGW W512 protocol shows 80–99% scale reduction under controlled conditions, and it does that with no salt, no drain, no electricity, and media that lasts roughly 3 to 7 years. If your only goal is protecting a water heater from scale, it's a legitimate tool. But it is a conditioner and a scale inhibitor, not a softener — and any company that calls it a "salt-free softener" is using the wrong word on purpose.

Buy the outcome you want. Soft water you can feel, spots gone, soap working properly: salt-based ion exchange. Scale prevention without salt, drain, or power, with everything else unchanged: TAC. They are not interchangeable.

FeatureSalt-based softenerSalt-free conditioner (TAC)
Removes hardnessYesNo — minerals stay in water
Spots goneYesNo
Soap lathers betterYesNo
Scale preventionYesYes (80–99% in lab tests)
Needs saltYesNo
Needs drainYesNo
Needs electricityYesNo
Ongoing costSalt + water for regenerationMedia replacement every 3–7 years

How to size a softener

Softeners are rated by grain capacity — how much hardness the resin can remove before it needs to regenerate. The goal is a unit that regenerates about once a week at an efficient salt setting. The math:

People × gallons per person per day × hardness (gpg) = grains per day

The Water Quality Association's design figure is 75 gallons per person per day (modern homes with efficient fixtures run closer to 55–60 — use your real metered number if you have it). Multiply grains per day by 7 days, add a reserve, and round up to the next standard size: 24,000, 32,000, 40,000, 48,000, 64,000, or 80,000 grains.

Worked example: a family of four, 75 gallons each per day, 10 gpg water. That's 4 × 75 × 10 = 3,000 grains a day, or 21,000 a week. At an efficient salt setting a softener delivers about 75% of its rated capacity, so you need a unit rated for at least 28,000 grains — which rounds up to a 32,000-grain (32k) softener.

If your water has iron, add it to the math. Dissolved iron consumes softening capacity. The industry convention is to add about 4 gpg of "compensated hardness" for every 1 ppm of iron. A well at 15 gpg hardness with 1 ppm iron gets sized as 19 gpg. Skip this step and your softener will regenerate constantly and still leave you with hard water.

Well water adds complications

City water softening is straightforward: measure hardness, size the unit, done. Well water usually brings friends.

Iron plus hardness. The most common combination. If the iron is dissolved (ferrous), under 5 mg/L, and your pH is above 6.7, a softener with fine-mesh resin can handle both in one tank — that's Penn State Extension's guidance. The AFWFilters Iron Pro 2 is built for exactly this: a salt-based softener on a Fleck 5600SXT metered valve with fine-mesh resin. AFWFilters rates it for iron up to 6 ppm, but size to Penn State's 5 mg/L. The 48,000-grain size runs about $800 (Walmart, late Oct 2026; $815 on Amazon, checked Nov 9, 2026). It does not remove hydrogen sulfide.

[AFFILIATE LINK: AFWFilters Iron Pro 2]

If iron is above 5 mg/L, or it's ferric (oxidized) iron, you need a dedicated iron filter ahead of the softener. Iron ahead of the softener protects the resin — iron fouls standard resin, and replacing a resin bed costs more than the iron filter would have.

Low pH plus hardness. Penn State advises against a softener alone when pH is below 6.7. Acidic water plus a softener is a corrosion problem waiting to happen. Fix the pH first with a calcite neutralizer, then soften.

Hardness plus sulfur plus iron. A staged system, in order: iron/sulfur filter first, softener second, UV last if bacteria are also in the picture. Each stage protects the next one.

The running costs nobody mentions

A softener's sticker price isn't the whole cost. Salt is the ongoing one — a family of four goes through several 40-pound bags a year, depending on hardness and water use. Regeneration uses water, which goes down the drain. And check your local rules before buying: parts of California, Texas, Michigan, Connecticut, and Massachusetts restrict brine discharge to septic or sewer, and some localities ban salt-based softeners outright. If you're on a septic system, check with your county — brine discharge is the question to ask.

TAC conditioners avoid all of that — no salt, no drain, no wastewater — but the media needs replacing every 3 to 7 years at several hundred dollars, and it does nothing for spots, soap, or feel. Over ten years, the ownership costs often come out closer than the sticker prices suggest.

When a salt-free conditioner makes sense

  • Your hardness is moderate (3.5–7 gpg) and your only complaint is scale
  • You can't run a drain line where the system would go
  • Your area restricts brine discharge
  • You don't want the maintenance of salt and regeneration
  • You're protecting a water heater or boiler, not chasing soft-feeling water

If any of those fit, TAC is a reasonable buy. If you want spots gone and soap working, it isn't — no matter what the brochure says.

What your test says to buy

  • Hardness under 7 gpg, scale is the only complaint: a salt-free conditioner is a reasonable buy.
  • Hardness over 7 gpg: a salt-based softener, sized to your grains per day.
  • Hardness plus dissolved iron under 5 ppm: AFWFilters Iron Pro 2 — one tank handles both.
  • Hardness plus iron over 5 ppm, or ferric iron: an iron filter first, then a softener.

FAQ

Does a salt-free water softener actually soften water?

No. Salt-free systems (TAC conditioners) change hardness minerals into crystals that don't stick as scale, but the minerals stay in the water. Only a salt-based ion-exchange softener removes hardness. A test after a TAC unit reads the same hardness as before.

What size water softener do I need?

Multiply people × ~75 gallons per day × hardness in gpg to get grains per day, then multiply by 7 days and round up to the next standard size (24k, 32k, 40k, 48k, 64k, 80k). Add about 4 gpg for every 1 ppm of dissolved iron. A family of four at 10 gpg needs a 32k softener.

Can a water softener remove iron?

Only dissolved (ferrous) iron, under 5 mg/L, with pH above 6.7 — per Penn State Extension. Above that, or with ferric iron, you need a dedicated iron filter ahead of the softener.

Is softened water safe to drink?

Yes. Ion exchange adds a small amount of sodium — roughly the same as a slice of bread per liter at typical hardness levels. People on strict low-sodium diets sometimes use potassium chloride instead of salt, or put a reverse-osmosis unit at the kitchen tap for drinking water.

Will a softener fix sulfur smell?

No. A softener removes hardness, not hydrogen sulfide. Sulfur smell needs its own treatment — Sulfur Smell in Well Water.

How many grains is my water?

Your lab report lists hardness in mg/L or grains per gallon. Divide mg/L by 17.1 to get grains per gallon. Under 3.5 gpg is soft; 7–10.5 is hard; over 10.5 is very hard. The number sizes your softener — see the sizing section above.